Why is ospho the only recommended rust converter

Media blasting with crushed glass is what I do.

This is the underside of the hood on my '68 GTX when I first started media blasting it. You can see how nice it works:

Inner Supports Media Blasted.JPG


Here's what it looks like when going over the media blasted metal with 80 grit on a Dual Action Sander.
DA 80 Grit over blasted metal.JPG
 
I guess I have to sand down the metal enough to get beyond the pits? I was just worried that I would remove too much metal. I have tried 80 grit on DA and it doesn’t seem to remove the pits.
 
Dip it or blast it.
I can’t dip the car. I’m too far along w the restoration. I didn’t know about the pits bc years ago I coated the entire car in Fertan thinking it would protect the metal while I did the pans. The pits might have been there before bc the entire car had oxidation from when the PO sanded off the paint and then let it sit for 20+ years in his garage unprotected.
 
Have you tried 36 and 80 grit on a DA? Or even something like an 8” mud hog. I don’t see how you can use ospho etc on a whole car.

Dipping might be an option but not sure if there are any dippers on Mars… :D
I have not tried 36 grit yet. I have tried 80 with no success. I was worried that the 36 would remove too much metal thickness.
 
You can thin the metal too much with 36 grit. It would take a while but you could sand holes in it eventually, Blasting is your best option IMO.
 
I need help with how to handle all the 1000’s of tiny pits in my sheet metal. I tried Ospho but it didn’t seem to touch the pits. I tried 3M Scotch-bright Rolocs, a surface conditioner tool etc but they remain. Advise is much appreciated. I am a hobbyist and this my Porsche 356 that sat unpainted but indoors for many years. The unprotected surface developed tiny rust pits all over it. I am not planning on painting the car right now. I’m going for a bare metal finish w something like Sharkhide, but I know I need to stop the rust first.
How long did you leave the Opsho on? Before you go to aggressive sanding I would make sure you've tried leaving the acid on for a few hours and while it's wet scrubbing with a coarse scuff pad (I use the Duragold gold color - it's 150grit). Sometimes it takes a while for the cocktail to get into the small pits. I find another thing that helps lift out small rust pits is cleaning while doing acid work. I'll grab a new microfiber (why I keep cheap ones on hand) and wet it with distilled water and wipe the surface down. It helps lift any gunk off the surface the process is creating and gives the next application more bite...then more Ospho and you'll see the surface get brighter and cleaner. Sounds labor intensive but it's quick and not very wasteful, I'll keep empty dip cans for filling with acid and dipping my scuff pad in...can use this amount for the whole roof of a car.
 
Every square inch of the car is pitted. I can’t imagine trying to fix that with ospho. The magnitude of the effort needed is huge….

Blasting all that is almost certain to distort the metal.

Maybe it’s time to back up, undo some stuff and get it dipped.
 
Last edited:
Every square inch of the car is pitted. I can’t imagine trying to fix that with ospho. The magnitude of the effort needed is huge….

Blasting all that is almost certain to distort the metal.

Maybe it’s time to back up, undo some stuff and get it dipped.
I have blasted before and of course this is an option, though a very messy one. Dipping is absolutely out of the question. The car is way to "assembled" for this option. The Ospho I have is very old, does it have a shelf life? Additionally, as suggested by Airheated, I have not left the Ospho on the car for a long period bc I am an impatient person. I will by some new material and be more patient. I agree, that sanding with 36 will be too aggressive as that is what I use for welding grinds.
 
I can't imagine the acid in Ospho would weaken from being old, but it's cheap enough I'd get another bottle to rule it out if I was worried. It took me a while to learn to be patient with the stuff, much of that was learning to work on other projects while it's doing it's thing. Those little pits are a PITA to remove, but the acid will get in there specially with wiping and scuffing which helps break away the shit plugging up the pores of the steel. Using SPI water-based w&g remover before and after the acid work really does help as well. The juice needs time for the chemical reaction to happen, and the scuffing every 20min or so helps break off the little rust "plugs" that are stuck in the pores of the steel.
 
Every square inch of the car is pitted. I can’t imagine trying to fix that with ospho. The magnitude of the effort needed is huge….

Blasting all that is almost certain to distort the metal.

Maybe it’s time to back up, undo some stuff and get it dipped.
I disagree with that assessment.
If you keep the air pressure down and hold the tip at a slight angle to the surface, it generates next to no heat at all. Personally, I have never had any metal warp when media blasting.

I have a 20 gallon blasting pot that I use for anything that can't fit in the blasting cabinet.
 
I disagree with that assessment.
If you keep the air pressure down and hold the tip at a slight angle to the surface, it generates next to no heat at all. Personally, I have never had any metal warp when media blasting.

I have a 20 gallon blasting pot that I use for anything that can't fit in the blasting cabinet.
Well then I guess we have to agree to disagree. Metal distortion with blasting has nothing to do with heat. It is the peening action of the media hitting the panel that generates distortion. Yes hitting it an angle helps because it reduces the impact force. It’s just not as effective in deep pits when you hit it at an angle.

The pits that were posted look quite deep to me, hence my concern regarding blasting.

Although I’ve never warped any panels with blasting I’ve had a few customers drop off panels that they decided to have blasted and were badly warped. Deck lids and hoods mostly.
 
Last edited:
I have blasted many times and never had any warping, but I am careful. The pits are not terribly deep and blasting would probably be the best, but I really hate blasting. It just sucks, but not like the other options are great. I will first try to be more patient and see if the chemical will do it. If not, blasting may be the only option. I was not planning on painting the car. Originally, I was going to leave it as if for the rat rod look, but when I saw that the rust pits were there, I decided I don't want to leave that alone. So I may be forced to paint the car if I go to the trouble of getting rid of all the pits.
 
Glad I found this forum. I'm on one for Oldsmobiles a lot of them use por 15, I probably would have too.

Search on POR 15 on this site... it will be enlightening and make you understand if this is a car you want to preserve you DON'T use that junk on it. The automotive industry is NOT what that stuff was designed for. It works fine for what it was designed for (extending the life of off-shore oil rigs) but not for the automotive industry.
 
Back
Top